An industrial controller is an automation device that can be used as a controller to operate reliably in an industrial environment. With the continuous development in the field of industrial automation, industrial controllers have been widely used in industrial automation, self-service terminals, medical equipment, rail transportation, communications, finance, network security and other fields. Installation-type faults refer to the faults that occur when industrial controllers install operating systems or application software. As the center of industrial control, the normal operation of industrial controllers is related to the stable and efficient operation of the system, users should master how to accurately and effectively deal with industrial controller failure.
Possible failure phenomenon
1. Industrial control machine in the installation of the operating system, file copying process down or error; in the system configuration down or error.
2. Industrial control machine in the installation of application software error, reboot, downtime and so on.
3. The system of industrial control machine is abnormal after the installation of hardware equipment (such as black screen, not start, etc.).
4. Application software can not be installed after uninstallation, or can not be uninstalled.
Possible components involved
Disk drives, industrial motherboards, CPU, memory, and other possible components, software.
Failure to determine the main points
I. Preparation before maintenance
Prepare disk data cable; the latest driver for the corresponding hardware devices.
II. Software installation
1. Check the connection and appearance of hardware devices
(1) Check whether other devices connected to the industrial computer work properly.
(2) Whether the connection line between the equipment is connected to the wrong or missed. Connection plug, seat pins are deformed, missing, short-circuit and other phenomena.
(3) Carefully check the error message to determine the possible parts of the fault.
(4) Observe whether the hardware equipment has a strange odor and check the temperature of the components.
(5) Whether the speed of the CPU fan of the industrial computer is too slow or unstable.
(6) Whether the driver of the industrial control machine is working with abnormal sound.
2. Other aspects of the check
(1) Comparison of the software manual, to confirm that the software and hardware configuration of the industrial computer in line with the use of requirements.
(2) Observe whether the installation medium is intact.
III. Equipment installation
1. Whether the equipment and components to be installed in the industrial computer are connected correctly, whether the connecting cable is intact, and whether there is a lack of pins, broken pins or shorted pins.
2. Whether the driver of the equipment is intact.
IV. Failure to determine the main points
1. Installation of the operating system
First: check the CMOS settings, if necessary, restore to factory settings. Second: pay attention to the parameters of the hard disk, CPU temperature, etc.. Observe whether the information displayed during the self-test of the industrial computer is consistent with the actual hardware configuration.
2. Installation of software
First: check whether there is a virus. Second: Check whether the partition table is correct and whether the partition is active. Use the Fdisk /mbr command to ensure that the master boot record is correct (after using this command, the ICPC can not start, proving that there is a virus or error in the original system, the hard disk of the ICPC should be done to initialize the operation). Finally: check whether there is a third-party memory-resident program in the system.
3. Installation process
(1) If when copying the file, reported CAB and other file errors, you can pay to try to copy the original file to another hard disk and then install. If normal through, the original installation media have problems, you can go to check the media and the corresponding drive is faulty; if you still can not copy, you should check the industrial computer disk drives, data lines, memory and other components.
(2) If the use of overlay installation and the report CAB and other file errors, replace the installation media. If the fault still exists, the industrial computer hard disk should be initialized first, and then reinstalled. If still can not be resolved, then consider the industrial computer hardware.
(3) installation process, in the detection of hardware error messages, blue screen or downtime, etc., one is to restart the industrial computer a number of times to see if it can be passed; the other is to check the software under the minimum system can be passed. If it can not pass, you should check the memory, disk, CPU, power supply and other components in the software minimum system in turn. If it can be installed normally, it is the failure or configuration problems of the components outside the software minimum system, which can be completed through the installation, gradually add those components, and determine whether there is a failure or improper configuration.
V. Hardware and other problems
1. If the system reboots or loses power when installing the system, ask for a test under the software minimum system. If the fault disappears, after installing the system, connect the devices outside the software minimum system one by one to check which component causes the fault and solve it with the replacement method; if the fault can not disappear, you should check the power supply, industrial motherboard and memory, and even the disk drive in the software minimum system.
2. Installation of hardware equipment
(1) whether the installed equipment, components are recognized in the self-test process of the industrial control machine, or can be recognized by the operating system. If not recognized, you should check the BIOS settings of the ICPC and the device itself, including jumpers and the corresponding slots or ports.
(2) Check whether there is any conflict between the newly installed devices of the industrial computer and the devices in the original system; see whether the fault is eliminated by changing the installation order of the driver, removing the corresponding parts or devices in the original system, and replacing the slots. If it can not be eliminated, it is incompatible.
(3) Whether the added equipment matches the technical or physical specifications of the current system.
(4) Check whether some settings in the current system have mismatches with the drivers of the installed components or devices.




