Industrial control machine failure again? Don't panic, this is how to solve it!

Mar 19, 2025 Leave a message

Industrial controller is a kind of industrial control computer, which uses the bus structure to detect and control the production process, electromechanical equipment and process equipment. Industrial control machine has computer motherboard, hard disk, CPU, memory, peripherals and interfaces, operating system, control network and protocols, computing power, friendly human-machine interface and other important computer characteristics. Industrial control industry products and technology is very special, belongs to the intermediate products, for other industries to provide stable, reliable, embedded, intelligent industrial computer.


Five common failures of industrial control computer


First, the electrical connection failure As the task is to adapt to a variety of harsh working environments, the site will inevitably produce a large amount of dust or vibration. Prolonged vibration can cause some parts of the connector to loosen, resulting in poor contact and other problems. This type of problem is difficult to determine, and it is usually easier to find faults at the user's site.


Second, software failure including incorrect application software settings, operating system failure or damage and viruses, the possibility of this type of failure in all the reasons should be very high.


Third, the use of environmental faults caused by the use of environmental causes include: electromagnetic interference, power supply instability, high or low temperature of the working environment, or even a lightning strike and other factors.


Fourth, the aging fault refers to the failure caused by the aging of the industrial control machine, but along with the upgrading and progress of electronic technology, this kind of failure is less and less.


Fifth, human failure mainly refers to the user is not familiar with the production characteristics of industrial control machine, using the wrong method of obstacles. Common Failures and Solutions of Industrial Computer With the continuous development of industrial computer technology, industrial computers have been widely used in the industrial production process, therefore, we need to familiarize ourselves with the causes of industrial computer failures and methods of treatment.


Below, we give the corresponding solutions to the common failures of industrial computers.


First, the industrial computer after power, the power supply works normally, the motherboard does not have any response? First of all, remove the peripheral cards and connected devices to see if they can start? If there is no response, remove the memory to see if the alarm? Then check if the CPU is working properly? Finally, replace the motherboard and check whether the motherboard is normal.


Second, the motherboard can work normally after booting, the BIOS detects the keyboard part and reports a keyboard error? First, check if the keyboard lock is locked and release the keyboard lock. If not, check whether the connection between the motherboard and the baseboard is correct, and whether the keyboard and mouse are connected correctly.


Third, after powering up the power indicator on the baseboard, light up a bit and then go out, can not power up? First, see if there is a foreign object in the chassis to cause a short circuit. Second, check whether the power cord is reversed, resulting in a short circuit to ground. Again, replace the power supply, motherboard, backplane and other equipment.


Fourth, after the boot hear the sound of the motherboard self-test but no display on the monitor:

1, check whether the monitor is connected to the host is normal;

2, clear CMOS (may be set up incorrectly) or replace the BIOS;

3, replace the CPU board (motherboard integrated graphics) or monitor.


Fifth, the industrial computer startup time is too long:

1, run the disk defragmentation program to eliminate debris;

2, the system startup file of the self-startup items off;

3, run the disk cleanup program to eliminate junk files;

4, adjust the network settings.


Sixth, after the boot memory self-test does not match the actual capacity:

1, check whether the motherboard video memory is shared with the motherboard memory, so that it will be divided from the memory as part of the video memory;

2, check whether the memory is a small particle memory, because some of the old chips do not support large particle memory, plugged in only half of the capacity;

3, a very small part of the motherboard uses a more special CPU, occupying part of the memory as an instruction decoder for CPU instruction set conversion, thus causing the memory capacity does not match.


Seven, turn on the power supply and the industrial computer does not respond:

1, check whether the power outlet is energized, and whether the connection with the industrial computer is normal;

2, check whether the power supply fan rotates after power on, whether the monitor is connected to the host is normal;

3, pull out the memory stick boot whether the alarm;

4, replace the CPU or motherboard.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry